Carrier 58TMA 7SI Gas Furnace Owners Manual

Product Specification
CategoriesCarrier HVAC Manuals
Document TypeHeating, Ventilating and Air Conditioning Manual Free Download. HAVC Operator's Instruction Manual.
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 24 pages
LanguageEnglish
Product BrandCarrier. Support Phone Number: In North America, please call 1-800-CARRIER for immediate customer assistance from 8:00a -5:00p (EST) weekdays , Heating, Ventilating and Air Conditioning - HVAC
Document File TypePDF
Publishercorp.carrier.com
Wikipedia's PageCarrier Corporation
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

58TMA Downflow/Horizontal 2-Speed, 2-Stage, Induced-Combustion Gas Furnace Visit www.carrier.com Installation, Start-Up, and Operating Instructions Sizes 065-125, Series 110 or 120 NOTE: Read the entire instruction manual before starting the installation. This symbol indicates a change since the last issue. Index Page SAFETY CONSIDERATIONS .1 ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS PROCEDURE .2 INTRODUCTION .3-4 Dimensional Drawing .2 Clearances to Combustibles 3 LOCATION 4 General 4 Location Relative to Cooling Equipment 4 Hazardous Locations .5 AIR FOR COMBUSTION AND VENTILATION 5 Unconfined Space .5 Confined Space .5 AIR DUCTS .6 General Requirements .6 Ductwork Acoustical Treatment .6 Supply Air Connections 6 Downflow Furnaces 6 Return Air Connections 8 Downflow and Horizontal Furnaces 8 SUPPLY-AIR PLENUM INSTALLATION (DOWNFLOW) 8 Installation On Combustible Floor .8 HORIZONTAL ATTIC INSTALLATION .8 HORIZONTAL CRAWLSPACE INSTALLATION 9 FILTER ARRANGEMENT .9 GAS PIPING 9 ELECTRICAL CONNECTIONS .11-12 115-v Wiring .11 24-v Wiring 11-12 Accessories 12 VENTING 13 START-UP, ADJUSTMENT, AND SAFETY CHECK .13-24 General .13-15 Sequence of Operation 15 Adaptive Heating Mode 15-16 Non-Adaptive Heating Mode .16 Cooling Mode .16 Continuous Blower Mode .16-17 Heat Pump Mode 17 Defrost Mode 17 Start-Up Procedures .17-18 Adjustments .18-23 Set Gas Input Rate 18-19 Set Temperature Rise 19-23 Set Thermostat Heat Anticipator 23 Check Safety Controls 24 Checklist 24 ama CANADIAN GAS ASSOCIATION ® A PP R O VED R REGISTERED QUALITY SYSTEM SAFETY CONSIDERATIONS Installing and servicing heating equipment can be hazardous due to gas and electrical components.

Only trained and qualified personnel should install, repair, or service heating equipment. Untrained personnel can perform basic maintenance functions such as cleaning and replacing air filters. All other operations must be performed by trained service personnel. When working on heating equipment, observe precautions in the literature, on tags, and on labels attached to or shipped with the unit and other safety precautions that may apply. Follow all safety codes. In the United States, follow all safety codes including the National Fuel Gas Code (NFGC) NFPA 54-1996/ANSI Z223.1-1996 and the Installation Standards. In Canada, refer to the current edition of the CAN/CGA-B149.1- and .2-M95 National Standard of Canada, Natural Gas and Propane Installation Codes (NSCNGPIC). Wear safety glasses and work gloves. Have a fire extinguisher available during start-up and adjustment procedures and service calls. Recognize safety information. This is the safety-alert symbol. When you see this symbol on the unit and in instructions or manuals, be alert to the potential for personal injury. Understand the signal words DANGER, WARNING, and CAUTION. These words are used with the safety-alert symbol. DANGER identifies the most serious hazards which will result in severe personal injury or death. WARNING signifies hazards which could result in personal injury or death. CAUTION is used to identify unsafe practices which would result in minor personal injury or product and property damage. NOTE is used to highlight suggestions which will result in enhanced installation, reliability, or operation. These instructions cover minimum requirements and conform to existing national standards and safety codes. In some instances, these instructions exceed certain local codes and ordinances, especially those that may not have kept up with changing residential construction practices. We require these instructions as a minimum for a safe installation.

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website